![]() Open the Trunk and locate the rear of the tail light.Change it yourself and save a trip to the dealer: Replacing the Bake Light costs a whopping $15 at the dealer when the part only costs $2 bucks at PepBoys. Make sure the the lid slides back into the rear notches (see picture) then press down and snap the latches back into place. Replace the old air filter with the new one and put the lid back by pushing it downward and inward (towards the engine).Gently pull the compartment lid outward (toward the fender) and upward at the same time until you can reach the air filter below. Located the air filter compartment and release the two metal latches. The part costs $13.95 and you can change it yourself in 5 minutes. Replacing the Engine Air Filter costs $33 at Jiffy Lube or $39 at the Dealer. Replace the plastic cover, and snap the glove compartment back into place. Now slide out the dirty Air Cabin Filter and slide in the new one. Simply remove it by squeezing the two plastic latches on either side of the cover. Located behind the glove compartment is a plastic cover keeping the Air Cabin Filter in place.Simply press in the plastic on the left side allowing the notch to bypass the dash & open the glove compartment all the way down. On the left hand side, note the notch that prevents the compartment from opening further. The filter itself costs $14.95 and you can replace it yourself in 5 minutes: ![]() Replacing the Cabin Air Filter costs $43 at Jiffy Lube or $45 at the Toyota Dealer. Replace the light bulb and put the harness back and snap it into place by rotating it counter-clockwise. Turn the harness to the clockwise one quarter turn (click) and pull the harness outward (towards the front of the car).Once apart, simply slide out the old battery, insert the new and pop the pieces back together. Take care to do this slowly in order to prevent cracking or damaging the plastic on your remote (replacements from the Toyota Dealer are expensive). Now gently angle the knife outward until the remote top and bottom plastic shells pop apart.Insert the knife at the bottom of the remote (taking care not to scratch the plastic) and push it in at an angle close to 90 degrees (see picture). First get a dull but thin butter knife from the kitchen.The Keyless Remote for the Corolla contains a single CR2032 battery ($2.50) and can be replaced in a few minutes: Here’s how to do it all in 20 minutes or less. The DIY maintenance procedures I’ll cover in this article are: Replacing the key fob battery, the cabin air filter, the engine air filter and a brake light bulb. Recently though, there were a few things I’ve had to replace myself because the dealer just charged too damn much. It consistently goes 38 miles on a gallon of gas and costs nearly to nothing to maintain. Dispose of used batteries according to local laws.My 2004 Toyota Corolla is a great little car.Replace only with the same or equivalent type recommended by the manufacturer.Batteries can be purchased at your Toyota dealer, local electrical appliance shops or camera stores.Operate the lock or unlock switch and check that the doors can be locked/unlockedīe careful not to lose the battery or any other small parts.When installing the key cover and mechanical key, install by conducting 2 and 1 with the directions reversed.Insert a new battery with the “+” terminal facing up. In this case, remove the electronic key module in order to remove the battery. When removing the cover, the electronic key module may stick to the cover and the battery may not be visible. Remove the depleted battery using a small flathead screwdriver.Release the lock and remove the mechanical key.Operate the lock or unlock switch and check that the doors can be locked/unlocked.Make sure that the key cover is securely installed without any gaps between it and the key. Push the entire edge of the battery cover into the key.Īlign the key cover with the key and then press it straight into the key. Install the battery cover with the tab facing up.If the battery cover is difficult to remove, lift the edge to remove it. To prevent damage to the key, cover the tip of the flathead screwdriver with a rag.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |